• RF Power Switch
  • 推文至Facebook 推文至Plurk 推文至Twitter

  • hwin RF RF Remote Control Power Switch

    User Manual for hwin RF Remote Control Power Switch  

    1.  Product Specification:

    1. Built-in RF receiver
    2. Frequency: 315 MHz/433.92 MHz
    3. Voltage: 110VAC/60Hz
    4. Max. Loading: 1000W
    5. Built-in 5A fuse
    6. Receiving range:  15m  (open space)
    7. Maximum program setting:  up to 126 sets RF controller.

     

    2.  Installation for RF Remote Control Power Switch:

    1. “IN” port is the AC power input port, connected to 110VAC power source at home.
    2. “OUT” port is the AC power output port, connected to the controlled appliance.

    For example: lighting equipment.  ( or  luminaries / ballast ).

    (Note: Press the lever on terminal block, then insert the wire into terminal hole.)

     
       


      

     
     

    (Fig.1)  Installation for RF Power Controller.

     

     

     

     

    3.  Program setting for controlling an appliance by RF Controller:

    1. Install the RF Power Controller and the controlled appliance as Fig 1.
    2. Connect to power source (110VAC) at home.
    3. Switch   PRG  to ”ON”.  ( on the back side of the RF controller )
    4. Key in the 9-digit ID of the RF Power Controller by RF controller. The ID can be found on the RF Power Controller.     ( Ex.: ID is “01-0-000005”, then key in  “ 0 1 0 0 0 0 0 0 5 “  )
    5. Press   FUNC  key for one second and release.

         (The controlled appliance will be start up.  Ex: lamp will be turn on.)

    1. Then press the number button you have chosen for the controlled appliance.  Ex.: press   1  .

             (The controlled appliance will be turn off, start up and turn off sequentially. 

    Ex.: Lamp will be turn off, turn on and off, just like flash)

    1. Switch   PRG   to ”OFF”.  ( on the back side of the RF controller )

     

    4.  Operation for controlling an appliance by RF Controller:

    1. Press   1   button on RF controller, then the controlled appliance will be start up.

    ( For example:  lamp will be turn on. )。

    1. Press   /1   button on RF controller, then the controlled appliance will be turn off.

    ( For example:  lamp will be turn off. )。

     

    1.  Attention for  RF Remote Control Power Switch:
    1. Maximum Loading: 1000W.
    2. Built-in 5A fuse to protect  HLRP-3002/HLRP-4001 and the controlled appliance.
    3. Select suitable wires: 20 ~14 AWG。
    4. HLRP-3002/HLRP-4001 cannot be programmed over 126 sets RF controller.
    5. The more operation can be reference by the user manual of RF Controller.

     

  •  
     

     

    Model Name

    RF Remote Control Power Switch

    Model No.

    HLRP-3002

    HLRP-4001

    Frequency

    433.92 MHz

    433.92 MHz

    Input Power

    100-125V / 60Hz

    200-260V / 50Hz

    Input Wire

    2 wire(110V)

    2 wire(230V)

    Output Wire

    2 wire(110V)

    2 wire(230V)

    Rx Sensitivity

    -95dBm

    -95dBm

    Fuse

    10A

    5A

    AWG

    2mm(Max.)

    1.5mm(Max.)

    Power Loading

    1000W(Max.)

    1000W(Max.)

    Memory (RF

    Receiver)

    29 Sets (Memory Controller  Signal)

    29 Sets (Memory Controller  Signal)

     Remote Control

    9 Digits ID Learning Mode

    9 Digits ID Learning Mode

    Power( Initial)

    Normal-On

    Normal-On

    PACKAGE

    90 Pcs / Carton

    90 Pcs / Carton

    Dimension

    63 X 36 X 42 cm

    63 X 36 X 42 cm

    N.W / G.W

    13.5 Kgs / 16.5 Kgs

    13.5 Kgs / 16.5 Kgs

    FCC (Part15)

    Complied

     

    CE

     

    Complied